Battery Controller G4-48 / 48V 10,000 Watt solar panel wind turbine

You are bidding on a 48 Volt 100% DIGITAL battery controller to prevent over-charging by simple dumping or cutting of incoming power. With EZ 5-point connection bar. Universal model for 48 to 36 volts (60V to 40V peak) LONG LIFE digital model / 25 Million Cycles (75 Years+ service life) Come with mounting flanges on both components Our most versatile model is this 48 volt system that can be micro programmed by the operator to keep a 12 volt lead acid, gel, AGM, Li-ion, EB, etc. Fine tune to your needs with the simple programming buttons. (See video's - cut and paste the URL's into any web browser bar) https://youtu.be/81y50tpSads https://youtu.be/rVffRzl6zcY https://www.youtube.com/watch?v=f9_P2rfQzgs https://www.youtube.com/watch?v=f9_P2rfQzgs https://www.youtube.com/watch?v=IZRahrogJ_A https://www.youtube.com/watch?v=NZENiUNoHWo SEE a Great Video on how to use it below WIND/SOLAR 48 VOLT / 100 AMP  DUMP / DISCONNECT CHARGE CONTROLLER WITH BUILT IN DIGITAL DISPLAY AND INTELLIGENT DUAL PROCESSOR CONTROLLER (With Original "THEM" Thermodyne Controller
. Says THER on the board. Made with real high voltage rated parts.
Some people claim Thermodyne made but only boards stamped "THER" are genuine Thermodyne boards) For solar panels and solar IT CAN DISCONNECT THE INCOMING POWER  OR DIVERT IT TO A DUMP LOAD. Max solar amperage in divert (dump) mode is 48-60 V @ 100 amps. This is a big hybrid wind and solar charge controller. Use for wind or solar or both at the same time! Also use for hydroelectric or solar or both. User changeable settings -- Several controllers on the market only let you set the dump level! Connect multiple turbines and solar panels up to 100 amps worth at the same time Can divert the charging source from the batteries to the load, or dump both the batteries along with the charging source. You can connect both wind and solar at the same time. Reverse polarity protection Ultra low power consumption even with the volt meter on (almost negligible). You can even set the volt meter to turn off after in-activity. This is important to get the longest life out of the electronics. No body else has this! Dual (2) Microprocessor controlled -- Extremely  stable and very accurate Multiple user changeable settings, and trip points for many various system requirements and applications- You can change the dump point voltage level, end of dump voltage level, length of time in divert mode when end dump point voltage is reached Isolated Electronics Protection - Impossible to accidentally connect wind or solar directly to the circuit board. Battery Status digital LED - Lets you know your battery's actual voltage in real time! Green LED come on and then you know it's in dump mode or cut mode depending on how your relay lugs wired. Plug and Play - Long leads for easy termination to your 12 volt battery or battery bank. Battery regulator for both your wind and solar battery input power. This regulator can either dump extra power creating free hot water or heat or just cut off extra power to keep your batteries from over charging. This unit is a must for wind turbine applications as it uses a mechanical relay which can handle high voltage surges unlike solid state controllers. Battery Regulator- Cut/Disconnect Controller- Diversion Load Regulation- If you use it as a DIVERSION or DUMP load MODE then it uses almost no power when it is NOT dumping (energy efficient sensing) In DISCONNECT mode it draws .2 amps but that's good since that means you have too much power in your batteries anyhow. This High Amp unit can control battery  banks  connected  to 14 Wind Turbines or 40 Solar Panels ! Used to prevent battery over charging on Wind - Solar - Hydro A battery regulator diverts excess power to power some other useful device when ever your battery is full. Use the this excess power to make free hot water or to recharge an auxiliary battery bank, so many uses! An extremely robust unit! draws almost ZERO power while sensing! 99.998% electrically efficient while sensing! 100% MOSFETS - Built to take over 2 Billion cycles or about 85 years of switching for the average system. Battery regulator.

Charge regulator.

Charge controller. Dump load regulator. "Cut" charge controller. Diversion load regulator. Micro processor controlled.

Versatile raised steel mounting plate.

Measures 10" long by 7" wide by 3" tall.

Works for all Wind Turbines, Solar panels and Hydro.

For all voltages ranges in multiple battery banks.

No grounded IGBT's or MOSFETS - Lighting strike proof isolation. CUT -LOAD controller (No need to buy a dump load resistor) Electrically efficient. Draws only trace power while sensing !

Does not waste electricity while sensing in  diversion load mode!

HOW POWER DRAW DYNAMICS WORKS: If you use it as a DIVERSION or DUMP load MODE then it uses no power when it is NOT dumping (energy  efficient  sensing)  The modern way to monitor your battery from over charging is to have a diversion load that performs another task such as heating water when your battery is in danger of over charging. Shutting down the output of your wind turbine or your other renewable energy devices is old school thinking. Now-a-days most people dump their excess power into some other legitimate device optimizing their energy independence. Hot water from your excess power can be used for radiant heating in the winter or even in the hot summer months for washing cloths or dishes and for bathing. You will always find a need for hot water in your life. "Simple and ultra-reliable" - "A BULLET PROOF SYSTEM"

Returns Accepted for this item if it's within 30 Days